Description
Specification:
Brand: Holybro
Model: Kakute F4 v2.4 Stack
Optional Version: NO VTX/ With VTX
|
Kakute F4 v2.4 Flight Controller
( Manual)
|
MCU: STM32F405
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
5x UARTs (1,3,4,4,6,7)
128 Mbit Dataflash chip
Battery input voltage: 2S-8S
BEC 9V/3A – Optimized for DJI O3 Air unit
BEC 5V/2A
7x PWM Outputs (6 Motor Output, 1 LED)
Supports serial receivers (SBUS, iBus, Spektrum, TBS CRSF, ESLR).
Mounting – 30 x 30mm, Φ4mm hole with M3 Grommets
Dimension – 37x37mm
Weight – 7g
JST-SH1.0_8pin port (For 4in1 ESCs)
JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)
|
|
Tekko32 F4 Metal 4in1 50A ESC
( Pin Cable)
|
Continuous Current: 50A x4
Burst Current: 60A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 120 (V1.9 Version)
Dimensions: 48x37x6mm
Weight: 13.8g
Mounting holes: M4 30.5×30.5mm (M3 grommets included)
Features:
New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM Frequency: 16k to 96k
Separate drive & control circuit, this broadens the current capability of the drive circuit
while reducing the electrical interference to the control circuit.
|
| NO VTX Version |
without VTX Module |
|
With VTX Version
( Manual)
|
Model: Atlatl HV V2 VTX
Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Protocol?smart audio2.0
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
Dimensions: 35x25x7mm (Includes USB height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 9.3g
( VTX Table Link )
|
Package Included:
| NO VTX Version |
1x KAKUTE F4 V2.4 FC
1x Tekko32 F4 Metal 4in1 50A ESC
1x Electrolytic capacito: 1000uF 35v
1x 8pin to 8pin 1mm pitch 65mm cable
1x 8pin to 8pin 1mm pitch 25mm cable
1x JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x JST SH 6pin 100mm cable(for Caddx HD Systems)
|
| with VTX Version |
1x KAKUTE F4 V2.4 FC
1x Tekko32 F4 Metal 4in1 50A ESC
1x Atlatl HV V2 VTX
1x Electrolytic capacito: 1000uF 35v
1x 8pin to 8pin 1mm pitch 65mm cable
1x 8pin to 8pin 1mm pitch 25mm cable
1x JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x JST SH 6pin 100mm cable(for Caddx HD Systems)
1x 80mm SMA–MMCX Cable
1x JST GHR 4pin 150mm cable |
