Happymodel SuperX HD ELRS 1-2S AIO Flight Controlelr Built-in 12A ESC and UART ELRS Receiver for Digital Whoop RC Drone FPV Racing

Flight controller

SuperX HD ELRS

mso-font-kerning:0.0000pt;’>Betaflight 4.4.2 firmware ready

mso-font-kerning:0.0000pt;’>Firmware target: font-size:7.5000pt;mso-font-kerning:0.0000pt;’>CRAZYBEEF4DX
mso-font-kerning:0.0000pt;’>MCU:STM32F411CEU6 (100MHzmso-font-kerning:0.0000pt;’>, 512K FLASH)
mso-font-kerning:0.0000pt;’>Sensor: mso-font-kerning:0.0000pt;’>BMI270 or ICM42688P mso-font-kerning:0.0000pt;’>(SPI connection)
mso-font-kerning:0.0000pt;’>Power supply: mso-font-kerning:0.0000pt;’>1-2S Lipo Lihvmso-font-kerning:0.0000pt;’> battery input (DC mso-font-kerning:0.0000pt;’>2.8V~8.7mso-font-kerning:0.0000pt;’>V)mso-font-kerning:0.0000pt;’>, font-size:7.5000pt;mso-font-kerning:0.0000pt;’>only support 1s input for this drone
mso-font-kerning:0.0000pt;’>Built-in mso-font-kerning:0.0000pt;’>12mso-font-kerning:0.0000pt;’>A(each) Blheli_S 4in1 ESC Dshot3mso-font-kerning:0.0000pt;’>00 read

mso-font-kerning:0.0000pt;’>Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update

mso-font-kerning:0.0000pt;’>Bluejay ESC Firmware ready
mso-font-kerning:0.0000pt;’>Built-in 5V 1mso-font-kerning:0.0000pt;’>A Bmso-font-kerning:0.0000pt;’>EC
mso-font-kerning:0.0000pt;’>Built-in voltage detection

mso-font-kerning:0.0000pt;’>No betaflight analog osd chip

Onboard 4in1 ESC

mso-font-kerning:0.0000pt;’>Power supply: mso-font-kerning:0.0000pt;’>1-2mso-font-kerning:0.0000pt;’>S LiPo/LiPo HV

mso-font-kerning:0.0000pt;’>Current: mso-font-kerning:0.0000pt;’>12mso-font-kerning:0.0000pt;’>A continuous peak mso-font-kerning:0.0000pt;’>15mso-font-kerning:0.0000pt;’>A (3mso-font-kerning:0.0000pt;’> seconds)
mso-font-kerning:0.0000pt;’>Support mso-font-kerning:0.0000pt;’>ESC-Configurator and BLHELI_S Suite configurator
mso-font-kerning:0.0000pt;’>Factory firmware:mso-font-kerning:0.0000pt;’> Z-H-30 – Bluejay, 0.19, 48kHz
mso-font-kerning:0.0000pt;’>Default protocol: DSHOT3mso-font-kerning:0.0000pt;’>00

Onboard UART ExpressLRS 2.4GHz Receiver

mso-font-kerning:0.0000pt;’>RF Frequency: 2.4GHz

mso-font-kerning:0.0000pt;’>Antenna: enameled copper wire 31mm length
mso-font-kerning:0.0000pt;’>Telemetry output Power: <12dBm
mso-font-kerning:0.0000pt;’>Receiver protocol: mso-font-kerning:0.0000pt;’>CRSF
mso-font-kerning:0.0000pt;’>Default firmware version: ExpressLRS V3.0.1

mso-font-kerning:0.0000pt;’>The same hardware with Happymodel EP1 receiver

mso-font-kerning:0.0000pt;’>Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through